Step-by-step instructions on how to replace the Lid, Lid Handle and Lid Hinges on your Traeger Flatrock 3-Zone grill. Includes part numbers, required tools, and estimated time of completion.
Applies to: Flatrock 3-Zone
Part #: Grill SKU:: FTK0004 - Lid TF3CN59AU FTK0084 - Lid TF3CN59AN FTK0033 - Lid Handle TF3CN59AU FTK0085 - Lid Handle TF3CN59AN FTK0027 - Lid Hinges TF3CN59AU FTK0075 - Lid Hinges TF3CN59AN
Lid Replacement Steps
Tools Needed
- 1/2" Wrench
Estimated Time to Complete
- 10 minutes
Before Performing Any Replacement Steps:
- Turn burner knobs to OFF position, close the propane tank, and disconnect the regulator
- Unplug the grill from power
- Open the lid and remove the cooktop
- While a second person holds the lid, use a 1/2" sized wrench to remove the 4 nuts holding the lid to the grill's body.
- There are 2 nuts on either side of each hinge. With the 4 nuts removed, push the lid to one side to free the linkages, and then to the other side to fully remove the lid.
- With the lid fully removed, remove the other 4 bolts holding the linkages to the grill cavity.
- Install the new set. Start by installing the 4 linkages, 2 on each side by screwing them on with a nut.
- When attaching the linkages, it's important that the angled side of the linkage is on top.
- With all 4 linkages attached to the grill body, you can align the other end of the linkages with the grill lid.
- Align all 4 linkages with the screws on the lid (you will probably need a second person for this) once aligned, you can reattach the nuts and screw the lid into place.
Lid Handle Replacement Steps
Tools Needed
- Phillips Screwdriver
Estimated Time to Complete
- Less than 5 minutes
Before Performing Any Replacement Steps:
- Turn burner knobs to OFF position, close the propane tank, and disconnect the regulator
- Unplug the grill from power
- Open the lid
- Remove the old handle by unscrewing the 2 Phillip's-head screws holding the handle in place.
- Install the new handle, placing the washers between the handle and the lid and inserting the screws from the interior side of the lid.
Lid Hinge Replacement Steps
Tools Needed
- 1/2" Wrench
Estimated Time to Complete
- 10 minutes
Before Performing Any Replacement Steps:
- Turn burner knobs to OFF position, close the propane tank, and disconnect the regulator
- Unplug the grill from power
- Open the lid and remove the cooktop
- While a second person holds the lid, use a 1/2" sized wrench to remove the 4 nuts holding the lid to the grill's hinges.
- Push the lid to one side to free the lid from the hinges, and then to the other side to fully remove the lid.
- With the lid fully removed, remove the other 4 bolts holding the hinges to the grill.
- Install the 4 new hinges to the grill, 2 on each side by screwing them on with the provided nuts and washers.
- When attaching the hinges, it's important that the angled side is on top.
- With all 4 linkages attached to the grill body, align all 4 linkages with the screws on the lid (you will probably need a second person for this).
- Install the lid screwing on the 4 remaining nuts and washers to the lid.
Still need help?
If you need help replacing your part, or if you run into additional concerns after replacement, contact Traeger Support. We're ready to help 365 days a year.
If you need help replacing your part, or if you run into additional concerns after replacement, contact Traeger Support. We're ready to help 365 days a year.